Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
Just how do you feel about A Step-by-Step Guide to Installing a Bathtub?

Setting up a bath tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably challenging project. If the old bathtub is conveniently obtainable, the job can move immediately; if you need to open a wall to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub and also embeded in the brand-new one. Make certain you have certified yourself for the job and fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will assist you set up a new tub in your washroom if you have already purchased a new tub and do not need to change the setup of your previous water pipelines.
Your devices and also material list ought to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Safeguard the faucet in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type ought to be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Making use of the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bathtub up until the level reads degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water supply and examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has been made use of a minimum of when as this will settle it right into its final position.
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final placement.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, causing difficulties with dampness and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles utilizing water-resistant or waterproof glue as well as grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

As a passionate person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that excerpt was really useful. Please take the time to promote this content if you appreciated it. Thanks a lot for your time. Kindly stop by our website back soon.
Avoid further plumbing damage; call. Report this page